Welcome to the ProSpangle Training Course.
This course was created for you to learn the ProSpangle process at your own pace in your own time.
Each lesson is set up for you to achieve the highest level of success, so make sure you are following along in order. Only move on to the next lesson when you feel you have properly understood the information and can perform each step successfully.
If you have not been enrolled by your ColDesi Customer Care Representative please call 1-800-891-1094 for access.
We do encourage you to complete the entire course before opening a support ticket for one of our Bling support specialists. Please go through each lesson again, because there may have been something you missed the first time, which may answer your question.
Click HERE for additional Support-based self-help videos.
On behalf of the entire ColDesi team, we want to wish you the best of luck on your journey to “Achieving Your Dreams.”
Machine Set-Up & Introduction
Machine Set-Up
Leveling the Machine
Control Panel Overview
The Press Unit
Machine Operation
Powering On your Machine
Checking the Table after Powering On
How to Use the NEW Touch Screen – 2021 Model and Later
New Touch Panel Walk Through – 2021 Model and Later
Sending a Design to the Machine
Selecting a Design from Memory to Run
Setting Color Changes
Setting the Machine’s Start Point
Tracing the Design
Running a Design
Heat Pressing to a Shirt
Programming an Offset for Multiple Runs
How To Do a Design Repeat on the Control Panel
Deleting Designs from Memory
Miscellaneous Training
Removing a Press Unit to Change Size or for Cleaning
Loading a Press Unit with Spangle when Punch is Removed
Daily Maintenance
Oiling the Punches
Cleaning the Table
Cleaning the Punch Rollers
Cleaning the Bottoms of the Punches
The Waste Reels & How to Empty Them
Weekly Maintenance
Cleaning the Punches
Weekly Oiling of the Punches
Monthly Maintenance
Oiling the Color Change Bearings
Greasing the Hammer
Replacing the Press Unit Guides
Cleaning the Tape Sensor
Yearly Maintenance
X-Axis Cleaning & Greasing
Y-Axis Cleaning & Greasing
Greasing the Color Change Gear
Troubleshooting Guides
SP Unit 06 Error
How to Unjam a Punch
Adjusting Table Height for Flipped Spangles
How to Jig the Press Units
How to Format Machine Memory
As part of the On-Boarding process, your Customer Care Representative (CCR) will enroll you in the training course(s) you need access to. If you have not gotten in contact with your CCR yet, give them a call at 800-891-1094, and the will get you set-up for success.
0%
Machine Set-Up & Introduction
Machine Set-Up
Leveling the Machine
Control Panel Overview
The Press Unit
Machine Operation
Powering On your Machine
Checking the Table after Powering On
How to Use the NEW Touch Screen – 2021 Model and Later
New Touch Panel Walk Through – 2021 Model and Later
Sending a Design to the Machine
Selecting a Design from Memory to Run
Setting Color Changes
Setting the Machine’s Start Point
Tracing the Design
Running a Design
Heat Pressing to a Shirt
Programming an Offset for Multiple Runs
How To Do a Design Repeat on the Control Panel
Deleting Designs from Memory
Miscellaneous Training
Removing a Press Unit to Change Size or for Cleaning
Loading a Press Unit with Spangle when Punch is Removed
Daily Maintenance
Oiling the Punches
Cleaning the Table
Cleaning the Punch Rollers
Cleaning the Bottoms of the Punches
The Waste Reels & How to Empty Them
Weekly Maintenance
Cleaning the Punches
Weekly Oiling of the Punches
Monthly Maintenance
Oiling the Color Change Bearings
Greasing the Hammer
Replacing the Press Unit Guides
Cleaning the Tape Sensor
Yearly Maintenance
X-Axis Cleaning & Greasing
Y-Axis Cleaning & Greasing
Greasing the Color Change Gear
Troubleshooting Guides
SP Unit 06 Error
How to Unjam a Punch
Adjusting Table Height for Flipped Spangles
How to Jig the Press Units
How to Format Machine Memory