Student Dashboard

Please disable anti-virus software before installing any software application.

DigitalHeat FX i650 Training Course

By /

Welcome to the DigitalHeat FX i650Training Course.

This course was created for you to learn the DigitalHeat FX (DFX) process at your own pace in your own time.

If you have not been enrolled by your ColDesi Customer Care Representative please call 1-800-891-1094 for access.

Each lesson is set up for you to achieve the highest level of success, so make sure you are following along in order. Only move on to the next lesson when you feel you have properly understood the information and can perform each step successfully.

We do encourage you to complete the entire course before opening a support ticket for one of our DigitalHeat FX support specialists. Please go through each lesson again, because there may have been something you missed the first time, which may answer your question.

Click HERE for additional Support-based self-help videos.

On behalf of the entire ColDesi team, we want to wish you the best of luck on your journey to “Achieving Your Dreams.”

Introduction to Training

Important Information about Training
Lesson 1 of 3 within section Introduction to Training. You must enroll in this course to access course content.
Printing and Environmental Conditions
Lesson 2 of 3 within section Introduction to Training. You must enroll in this course to access course content.
Graphic Types – Bitmap vs. Vector
Lesson 3 of 3 within section Introduction to Training. You must enroll in this course to access course content.

SET-UP & PREPARATION

Unboxing the DigitalHeat FX i650
Lesson 1 of 5 within section SET-UP & PREPARATION. You must enroll in this course to access course content.
Unwrapping and Installing Toners
Lesson 2 of 5 within section SET-UP & PREPARATION. You must enroll in this course to access course content.
Plugging in the Global Power Supply
Lesson 3 of 5 within section SET-UP & PREPARATION. You must enroll in this course to access course content.
Installing the Print Optimizer (PO) Software
Lesson 4 of 5 within section SET-UP & PREPARATION. You must enroll in this course to access course content.
Installing Print Optimizer Software Part 2
Lesson 5 of 5 within section SET-UP & PREPARATION. You must enroll in this course to access course content.

Setting Up Your Heat Press

Setting Up the Hotronix Fusion Heat Press
Lesson 1 of 3 within section Setting Up Your Heat Press.
Programming Your Presets
Lesson 2 of 3 within section Setting Up Your Heat Press. You must enroll in this course to access course content.
Alternative Heat Press Instructions
Lesson 3 of 3 within section Setting Up Your Heat Press. You must enroll in this course to access course content.

Making Your First Shirt

Intro | Setting Expectations
Lesson 1 of 3 within section Making Your First Shirt. You must enroll in this course to access course content.
Making Your First Shirt with i650
Lesson 2 of 3 within section Making Your First Shirt. You must enroll in this course to access course content.
Marry Tips | Making a Transfer
Lesson 3 of 3 within section Making Your First Shirt.

Print Optimizer – Basic Features

Queues and Print Modes
Lesson 1 of 5 within section Print Optimizer – Basic Features. You must enroll in this course to access course content.
Importing Files | First 2 Steps
Lesson 2 of 5 within section Print Optimizer – Basic Features. You must enroll in this course to access course content.
Supersizing Your Graphics
Lesson 3 of 5 within section Print Optimizer – Basic Features. You must enroll in this course to access course content.
Resizing and Cropping
Lesson 4 of 5 within section Print Optimizer – Basic Features. You must enroll in this course to access course content.
Page Layout and Gang Printing
Lesson 5 of 5 within section Print Optimizer – Basic Features. You must enroll in this course to access course content.

Print Optimizer – Advanced Features

KnockmeOut Black
Lesson 1 of 4 within section Print Optimizer - Advanced Features. You must enroll in this course to access course content.
KnockmeColor Out
Lesson 2 of 4 within section Print Optimizer - Advanced Features. You must enroll in this course to access course content.
Copy, Duplicate and Gang Printing Different Sizes
Lesson 3 of 4 within section Print Optimizer - Advanced Features. You must enroll in this course to access course content.
Working with Transparency | Dots & Stripes
Lesson 4 of 4 within section Print Optimizer - Advanced Features. You must enroll in this course to access course content.

Bonus Content

Copyrights
Lesson 1 of 5 within section Bonus Content. You must enroll in this course to access course content.
Logo Placement | Article
Lesson 2 of 5 within section Bonus Content. You must enroll in this course to access course content.
Why Not to Use RGB Files
Lesson 3 of 5 within section Bonus Content. You must enroll in this course to access course content.
Using Snipping Tool
Lesson 4 of 5 within section Bonus Content. You must enroll in this course to access course content.
Color Matching
Lesson 5 of 5 within section Bonus Content. You must enroll in this course to access course content.

USING THE DK20 HEAT PRESS

Getting Set Up
Lesson 1 of 4 within section USING THE DK20 HEAT PRESS. You must enroll in this course to access course content.
EZ Peel Two Step Paper – The Marry Step
Lesson 2 of 4 within section USING THE DK20 HEAT PRESS. You must enroll in this course to access course content.
EZ Peel Two Step Paper – The Transfer and Finishing Steps
Lesson 3 of 4 within section USING THE DK20 HEAT PRESS. You must enroll in this course to access course content.
EZ Peel One Step Paper – The Process
Lesson 4 of 4 within section USING THE DK20 HEAT PRESS. You must enroll in this course to access course content.

Introduction to Training

Important Information about Training
Lesson 1 of 3 within section Introduction to Training. You must enroll in this course to access course content.
Printing and Environmental Conditions
Lesson 2 of 3 within section Introduction to Training. You must enroll in this course to access course content.
Graphic Types – Bitmap vs. Vector
Lesson 3 of 3 within section Introduction to Training. You must enroll in this course to access course content.

SET-UP & PREPARATION

Unboxing the DigitalHeat FX i650
Lesson 1 of 5 within section SET-UP & PREPARATION. You must enroll in this course to access course content.
Unwrapping and Installing Toners
Lesson 2 of 5 within section SET-UP & PREPARATION. You must enroll in this course to access course content.
Plugging in the Global Power Supply
Lesson 3 of 5 within section SET-UP & PREPARATION. You must enroll in this course to access course content.
Installing the Print Optimizer (PO) Software
Lesson 4 of 5 within section SET-UP & PREPARATION. You must enroll in this course to access course content.
Installing Print Optimizer Software Part 2
Lesson 5 of 5 within section SET-UP & PREPARATION. You must enroll in this course to access course content.

Setting Up Your Heat Press

Setting Up the Hotronix Fusion Heat Press
Lesson 1 of 3 within section Setting Up Your Heat Press.
Programming Your Presets
Lesson 2 of 3 within section Setting Up Your Heat Press. You must enroll in this course to access course content.
Alternative Heat Press Instructions
Lesson 3 of 3 within section Setting Up Your Heat Press. You must enroll in this course to access course content.

Making Your First Shirt

Intro | Setting Expectations
Lesson 1 of 3 within section Making Your First Shirt. You must enroll in this course to access course content.
Making Your First Shirt with i650
Lesson 2 of 3 within section Making Your First Shirt. You must enroll in this course to access course content.
Marry Tips | Making a Transfer
Lesson 3 of 3 within section Making Your First Shirt.

Print Optimizer – Basic Features

Queues and Print Modes
Lesson 1 of 5 within section Print Optimizer – Basic Features. You must enroll in this course to access course content.
Importing Files | First 2 Steps
Lesson 2 of 5 within section Print Optimizer – Basic Features. You must enroll in this course to access course content.
Supersizing Your Graphics
Lesson 3 of 5 within section Print Optimizer – Basic Features. You must enroll in this course to access course content.
Resizing and Cropping
Lesson 4 of 5 within section Print Optimizer – Basic Features. You must enroll in this course to access course content.
Page Layout and Gang Printing
Lesson 5 of 5 within section Print Optimizer – Basic Features. You must enroll in this course to access course content.

Print Optimizer – Advanced Features

KnockmeOut Black
Lesson 1 of 4 within section Print Optimizer - Advanced Features. You must enroll in this course to access course content.
KnockmeColor Out
Lesson 2 of 4 within section Print Optimizer - Advanced Features. You must enroll in this course to access course content.
Copy, Duplicate and Gang Printing Different Sizes
Lesson 3 of 4 within section Print Optimizer - Advanced Features. You must enroll in this course to access course content.
Working with Transparency | Dots & Stripes
Lesson 4 of 4 within section Print Optimizer - Advanced Features. You must enroll in this course to access course content.

Bonus Content

Copyrights
Lesson 1 of 5 within section Bonus Content. You must enroll in this course to access course content.
Logo Placement | Article
Lesson 2 of 5 within section Bonus Content. You must enroll in this course to access course content.
Why Not to Use RGB Files
Lesson 3 of 5 within section Bonus Content. You must enroll in this course to access course content.
Using Snipping Tool
Lesson 4 of 5 within section Bonus Content. You must enroll in this course to access course content.
Color Matching
Lesson 5 of 5 within section Bonus Content. You must enroll in this course to access course content.

USING THE DK20 HEAT PRESS

Getting Set Up
Lesson 1 of 4 within section USING THE DK20 HEAT PRESS. You must enroll in this course to access course content.
EZ Peel Two Step Paper – The Marry Step
Lesson 2 of 4 within section USING THE DK20 HEAT PRESS. You must enroll in this course to access course content.
EZ Peel Two Step Paper – The Transfer and Finishing Steps
Lesson 3 of 4 within section USING THE DK20 HEAT PRESS. You must enroll in this course to access course content.
EZ Peel One Step Paper – The Process
Lesson 4 of 4 within section USING THE DK20 HEAT PRESS. You must enroll in this course to access course content.
Student Dashboard

Contact Us

Copyright © 2021 ColDesi Training | Powered by ColDesi Training